Digital Devices Max M4 Multituner TV Card - the all-rounder for satellite, cable or terrestrial reception A 4-fold multi-band tuner HD TV Card / Tuner Card for the PCIe Slot for the following reception types: DVB-S(satellite tuner) DVB-S2 (satellite tuner) ISDB-S (satellite tuner) DVB-C (cable tuner) DVB-C2 (cable tuner) ISDB-C (cable tuner) J.83 (cable tuner) DVB-T(terrestrial tuner) DVB-T2 (terrestrial tuner) ISDB-T (terrestrial tuner) The Digital Devices Max M4 is a multi-tuner TV card. It has the capabilities of digital reception for satellite (DVB-S / S2 / ISDB-S), cable (DVB-C / C2 / ISDB-C / J.83) or terrestrial (DVB-T / T2 / ISDB-T). The reception of SD to Ultra HD modulated channels on the transponders of the provider is no problem for the M4. Due to the low power consumption of ~ 7 watts, the card works very economically. The Max M4 Multituner card comes in Full Profile Format (full height) with corresponding bracket. The choice of reception is done dynamically. The Max M4 has four individual front ends, depending on the tune request, the card switch automatically to a free cable, satellite or terrestrial tuner. Through the dynamically switching, a reprograming of the receiving mode during operation is not needed. Thus a DVB-C or DVB-T2 connection can be used for bad weather alternative with disturbed SAT reception, in order to keep a running operation. Receive stations from different sources, such as SAT and terrestrial, without investing in different receiving systems. If not only satellite, but also cable TV should to be received at a location(for example for local channels), this is now possible without any problems with the Max M4. For operation with a standard satellite receiving system (star cabling), you need a cable for each DVB-S tuner to the Max M4, thus also the card can be used with full DiSEqC support. Likewise, the use of Unicable I (EN50494) and Unicable II / JESS (EN50607) systems is easily possible. To supply the individual SAT tuners with a Unicable signal, the SAT inputs of the card are connected to the Unicable system by a Unicable splitter. For operation on a cable provider or terrestrial antenna, only one cable from the DVB-C wall socket or antenna is needed. The signal is internally distributed to the tuner, thus no splitter parts are needed.(IEC adapter to F socket for connection to antenna or BK system included in the scope of delivery) In the field of data analysis, you now receive the data from one source from different reception types, e.g. Advertising analysis, time offset, data rate of individual transmissions. Also the dynamic switching of the required reception type offers advantages, becuase a changing is immediately possible. The hardware design of the card allows an operation in the 24/7 envoirement for professional and home use. Thanks to the use of high-quality components, such as ceramic capacitors and the absence of environmentally hazardous substances, the Max M4 ensures a long lifetime even with permanent use of the hardware. The Digital Devices Max M4 can be extended with an Octopus Single-CI or Octopus Twin-CI card via an additional PCIe slot and of course also other connected Flex-CI modules from Digital Devices can be used. Drivers for Windows XP, Windows 7, Windows 8 (.1) as well as Windows 10 and Linux. * 1 Unicable® Requires Unicable® / SCR / CENELEC EN50494 compliant LNB or multiswitch to EN50494* 2 JESS® Requires Jess® / CENELEC EN50607 compliant LNB or multiswitch to EN50607      

Digital Devices MAX SX8 Basic (DVB-S2 / DVB-S2X 4/8) comes with 8x DVB-S/S2/S2X tuners on only one PCI Express card. With the Digital Devices MAX SX8 Basic Digital Devices presents an HDTV tuner card for the PCI Express slot with eight TV tuners. The ultra-compact design, only 5 watts power consumption, the choice of operating mode and support for the single-cable solutions according EN50494 (Unicable®)*1 and EN50607 (JESS®)*2, allows a flexible use in any situation and for any solution. Suitable on Windows 7, Windows 8(.1), Windows 10 and Linux, the Digital Devices MAX SX8 Basic can be integrated by flexible selection of the operating mode individually in the environment. The operating modes allows a single-cable mode according to EN50494 (Unicable®)*1 and EN50607 (JESS®)*2, the use of quad LNBs and 4 lines from multi-switches and Quattro LNB's or master output of a multiswitch. Operation Mode Quad LNB or 4 Multiswitch Outputs Use this option if you want to connect your Max SX8 Basic to a normal multiswitch or LNB with integrated multi-switch (QUAD LNB or OCTO LNB). For both cases, four SAT lines are required to provide a full-featured and full reception (all four levels SAT).   Operation Mode Quattro LNB or Multiswitch cascade output (VL, VH, HL, HH) Use this option if you want to connect your Max SX8 Basic to a multi-switch, which can be cascaded. Such multi-switch have in addition to the inputs for a Quattro LNB, four outputs which are also known as "cascade outputs". These outputs give only from a Quattro LNB received signals unaltered out again. Alternatively, the four outputs can be directly used by a Quattro LNB without multiswitch.   Operation Mode Singlecable Solution in this operation mode the card can be used over only one antenna cable via Unicable®*1 oder JESS®*2 supported equipment. Thereby it is possible to provide up to 8 Tuners by a UniCable® System and up to 32 Tuners with a JESS® System. More than one satellite can be used in this mode (in this mode, you need for 8 tuners only 1 cable to port 1, thanks to an integrated multi-switch).   Operation mode 4 Tuner Direct In the "4 Tuner" operating mode, the four inputs of the card can be used like individual tuners. Several satellites (DiSEqC) are supported in this mode. (In this mode you need 1 to 4 cables from a multi-switch or LNB with integrated multi-switch) The Digital Devices MAX SX8 Basic can be used immediately with numerous TV applications.   * 1 Unicable® Requires Unicable® / SCR / CENELEC EN50494 compliant LNB or multiswitch to EN50494* 2 JESS® Requires Jess® / CENELEC En50607 compliant LNB or multiswitch to En50607  

Digital Devices MAX SX8 (DVB-S2 / DVB-S2X 4/8) comes with 8x DVB-S/S2/S2X tuners on only one PCI Express card. With the Digital Devices MAX SX8 Digital Devices presents an HDTV tuner card for the PCI Express slot with eight TV tuners. The ultra-compact design, only 5 watts power consumption, the choice of operating mode and support for the single-cable solutions according EN50494 (Unicable®)*1 and EN50607 (JESS®)*2, allows a flexible use in any situation and for any solution. Suitable on Windows 7, Windows 8(.1), Windows 10 and Linux, the Digital Devices MAX SX8 can be integrated by flexible selection of the operating mode individually in the environment. The operating modes allows a single-cable mode according to EN50494 (Unicable®)*1 and EN50607 (JESS®)*2, the use of quad LNBs and 4 lines from multi-switches and Quattro LNB's or master output of a multiswitch. Operation Mode Quad LNB or 4 Multiswitch Outputs Use this option if you want to connect your Max SX8 to a normal multiswitch or LNB with integrated multi-switch (QUAD LNB or OCTO LNB). For both cases, four SAT lines are required to provide a full-featured and full reception (all four levels SAT).   Operation Mode Quattro LNB or Multiswitch cascade output (VL, VH, HL, HH) Use this option if you want to connect your Max SX8 to a multi-switch, which can be cascaded. Such multi-switch have in addition to the inputs for a Quattro LNB, four outputs which are also known as "cascade outputs". These outputs give only from a Quattro LNB received signals unaltered out again. Alternatively, the four outputs can be directly used by a Quattro LNB without multiswitch.   Operation Mode Singlecable Solution in this operation mode the card can be used over only one antenna cable via Unicable®*1 oder JESS®*2 supported equipment. Thereby it is possible to provide up to 8 Tuners by a UniCable® System and up to 32 Tuners with a JESS® System. More than one satellite can be used in this mode (in this mode, you need for 8 tuners only 1 cable to port 1, thanks to an integrated multi-switch).   Operation mode 4 Tuner Direct In the "4 Tuner" operating mode, the four inputs of the card can be used like individual tuners. Several satellites (DiSEqC) are supported in this mode. (In this mode you need 1 to 4 cables from a multi-switch or LNB with integrated multi-switch) The Digital Devices MAX SX8 can be used immediately with numerous TV applications.   * 1 Unicable® Requires Unicable® / SCR / CENELEC EN50494 compliant LNB or multiswitch to EN50494* 2 JESS® Requires Jess® / CENELEC En50607 compliant LNB or multiswitch to En50607  

Additional fan for Max serial cards for mounting on K5 slot bracket. The fan is optional and can be installed directly on the cards of the Max series to increase a overheat prevention in casing with higher heating or poor air circulation. A normal ventilation over casing fans is normally sufficient.