Prijzen excl. btw excl. verzendingskosten
Leveringstijd 10 Werkdagen
- Productnr.: 291057
HD / UHD network tuner. Unicast and Multicast Server certified according to SAT> IP 1.2.2 Standard with 2 Tuners for DVB-C / C2 - DVB-T / T2 - ISDB-T and 2x CI Slots
Stream your live TV signal from your cable or terrestrial antenna to compatible clients / players according to SAT> IP Standard or RTP / UDP MPTS Multicast Clients.
The Octopus NET can be used with all clients which work according to SAT> IP and are suitable for the playback of DVB-C / C2 / T / T2 / ISDB-T. For the use as a multicast server, clients must be able to handle MPTS streams. In both cases, e.g. Panasonic TVs can be used.
Using SAT> IP Apps or players, you can look anywhere Watch TV on your mobile device in your wireless network where you want or where no coaxial cable is or can be laid. SAT> IP Set Top Boxes are available for this purpose from many manufacturers. When selecting the client, make sure that it supports the reception modes of the Octopus NET server.
The Octopus NET can also be used as an IPTV head station. Thanks to multicast support for MPTS and IGMPv3 support, you can use the RTP and UDP protocols to stream a complete transponder in just one stream or single or multiple channels. Up to 12 parallel streams are possible without compromising quality or stability.
The Octopus NET is modular in design and allows a change of the installed receiving modules. When changing locations, the Octopus NET can be adapted or extended at any time by exchanging these modules in the reception situation.
The integrated CI slots allows decryption of channels in multicast as well as in unicast mode. In Unicast mode, one channel per CI slot can be decrypted witch a client which support the CI in Octopus NET - in multicast multiple channels of one transponder per CI slot. Please note the terms and conditions of the PayTV / Content providers listed in your contract to use the content.
Due technical reasons, the MTD function is not available for this device.
The built-in 5 port GigaBit Switch not only extends your network through additional LAN ports, but you can also define the streams to be available on the ports in multicast mode. The switch can also be used as IGMPv3 Querrier.
The master / slave IO system of the tuner modules eliminates the purchase of additional splitters and / or amplifiers. You only need one cable for all tuners installed in the unit. Tuner pairs can be connected among each other externally (IN / OUT).
Due to the low overall height, the Octopus NET adapts flexibly to your environment. Using the supplied wall bracket hanging or with visual gloss on the shelf. By the passive cooling of the device, the Octopus NET runs with absolute 0dB quietly without disturbing.
In running state with 2 active tuners, the power consumption of the Octopus NET is about 6 watts
A SAT>IP client or a player with RTSP support (eg VLC Player) is required to use the Octopus NET. In multicast mode a multicast client with MPTS support). The CI of the Octopus NET is not part of the SAT> IP specification and is therefore not supported by any client.
Here is a small overview of available clients. Further clients can be found on the SATIP info page: http://www.satip.info
This product was developed and produced in Germany and subject strict controls in the area of quality and environment protection.
|SAT>IP Standard:||nach V 1.2, und V1.2.2|
|Netzwerk:||5 Port GigaBit Switch|
|Stromverbrauch:||ca. 6 Watt|
The rack installation slot for 19 "server racks for slots with 1U for mounting the Octopus NET v2 models.
The installation slot is designed for holding 3 Complete Octopus NETs v2 or Octopus NET MCs with full equipment. The Octopus NET is fixed on the mounting points for wall mounting on the installation frame. For power supply the normal AC adapter of the Octopus NET can be used, this will also be attached to the mounting frame.
The Octopus NETs can be installed on the mounting frame so that either an access to the tuners and network switch or CI slots are accessible through the front openings.
Necessary mountingmaterials for installation in a rack and for attaching the Octopus NET are included.
Note: The 19-inch rack installation slot is compatible with the housings of the Octopus NET v2 and MC models. The models of the Octopus NET v1 can not be used here.
No Octopus NET or Octopus NET housing are included. Pictures are for illustration only